Xiaomi Redmi Note 6 Pro EDL Point

I am excited to bring you an in-depth guide on unlocking the full potential of the Xiaomi Redmi Note 6 Pro by accessing its EDL (Emergency Download) Mode.

What is EDL Mode and Why Should You Care?

EDL Mode, or Emergency Download Mode, is a powerful tool built into certain Qualcomm-powered devices, like the Xiaomi Redmi Note 6 Pro, that enables advanced functionality and flashing firmware. By accessing EDL Mode, you can unbrick your device, bypass FRP (Factory Reset Protection) lock, and unlock the bootloader, opening up a world of possibilities for customization and optimization. Also Read How to boot Redmi Note 7 to EDL & Fastboot Mod [test Point] 2023

Locating the Xiaomi Redmi Note 6 Pro EDL Point

Before you can access EDL Mode, you must first identify the EDL point on your Xiaomi Redmi Note 6 Pro. The EDL point is a specific set of test points on the device’s motherboard that, when shorted, forces the device into EDL Mode. Here’s how to locate the EDL point on your Xiaomi Redmi Note 6 Pro:

1. Power off your device and remove the back cover.
2. Carefully disconnect the battery connector.
3. Locate the two EDL test points on the motherboard. They are typically marked by small dots or circles.
4. Short the EDL test points using a pair of tweezers or a conductive tool.

Entering EDL Mode on Your Xiaomi Redmi Note 6 Pro

Once you have identified and shorted the EDL test points, you can follow these steps to enter EDL Mode:

1. With the EDL test points shorted, connect your device to a PC using a USB cable.
2. The device should now enter EDL Mode, and you will see a notification on your PC indicating that the device has been detected in “Qualcomm HS-USB QDLoader 9008” mode.
3. You can now use specialized software, such as MiFlash or QPST, to flash firmware and unlock advanced functionality.

Xiaomi Redmi Mi Note 6 Pro Into EDL Mode Using Test Points

In addition to the method previously discussed, there is another approach to force your Xiaomi Redmi Mi Note 6 Pro into EDL Mode using test points. This method requires you to disassemble your device, so proceed with caution and at your own risk. Here are the steps to follow:

1. Power off your Xiaomi Redmi Mi Note 6 Pro and remove the SIM card tray.
2. Use a plastic pry tool or a similar non-conductive tool to carefully remove the back cover of your device.
3. Remove all screws securing the protective plastic cover over the motherboard.
4. Detach the protective cover and disconnect the battery connector from the motherboard.
5. Locate the test points on the motherboard, which are usually marked by small dots or circles.
6. Short the test points using a pair of tweezers or a conductive tool while connecting your device to a PC using a USB cable.
7. Your device should now enter EDL Mode, and your PC will recognize it as “Qualcomm HS-USB QDLoader 9008.”

Important Note

Please be aware that attempting to enter EDL Mode, regardless of the method used, can potentially void your warranty, brick your device, or lead to other issues if not done correctly. It is highly recommended to follow expert guidance, consult reputable sources, and proceed with caution.

Always ensure that you have a backup of your important data before attempting to enter EDL Mode or flash firmware. Additionally, use a high-quality USB cable and ensure your device has sufficient battery life before starting the process.

How to Enter EDL Mode on Xiaomi Redmi Note 6 Pro Using a Different Method

If you prefer not to disassemble your device, you can try this alternative method to enter EDL Mode on your Xiaomi Redmi Note 6 Pro:

1. Enable USB debugging on your device by going to Settings > About Phone > tap the MIUI version 7 times to enable Developer Options.
2. Return to Settings > Additional Settings > Developer Options, and enable USB debugging.
3. Connect your device to a PC using a USB cable.
4. Download and install ADB (Android Debug Bridge) and Fastboot tools on your PC.
5. Open a command prompt or terminal window on your PC, navigate to the folder where ADB and Fastboot are installed.
6. Enter the following command to reboot your device into Fastboot mode: adb reboot bootloader
7. Once your device is in Fastboot mode, enter the following command to reboot into EDL Mode: fastboot oem edl
8. Your device should now enter EDL Mode, and your PC will recognize it as “Qualcomm HS-USB QDLoader 9008.”

Method 1: Fastboot Mode

1. Download and extract the ADB and Fastboot Tool to your PC. Preferably, save it in the C:/ Drive.
2. Turn off your device and prepare to access the bootloader. You can do this by pressing the Volume Down key and the Power button simultaneously until you see the MI logo on the screen.
3. Connect your device to your PC with a functional cable.
4. Navigate to the folder where you installed the ADB. Hold down the Shift Key, then Right Click.
5. From the drop-down menu, choose “Open Command Window from here”.
6. In the command window, type in one of the following commands:
   • fastboot oem edl
   • fastboot reboot-edl
   • fastboot reboot edl
7. Your device should now enter EDL mode, and the screen should light up.
8. Open the Device Manager on your PC.
9. Look under the port section. You should see either ‘Qualcomm HS USB Qdloader 9008’ or ‘MediaTek Preloader’. If you do, the drivers are functioning correctly.
10. Now, you’re ready to flash firmware or flash files as required.
11. That’s it! Your Xiaomi device should now be recognized in the device management section.

By following these steps, you can ensure a successful transition to EDL mode for your Xiaomi device.

Method 2: Using ADB

1. Download the ADB and Fastboot Tool onto your PC.
2. Extract the downloaded tool into your C:/ Drive.
3. Using a reliable USB cable, connect your smartphone to your PC.
4. Open the adb command interface. You can do this by navigating to the extracted ADB and Fastboot Tool folder, then press and hold the Shift Key + Right Click in the empty space inside the folder. From the context menu, choose “Open command window here” or “Open PowerShell window here”.
5. Type the following command into the command line or PowerShell window: adb reboot edl
6. Press Enter. Your device should now reboot into EDL mode.

Method 3: Using hardware keys

Here’s an alternative method for booting your Xiaomi Mi Max into EDL mode that is user-friendly and straightforward. First, power off the smartphone and have a USB cable at hand. Connect one end of the cable to your computer’s USB port, leaving the other end disconnected from the device. Before proceeding, ensure you’re comfortable with the steps. Now, simultaneously press and hold the Volume Up and Volume Down buttons on your device. While maintaining this button combination, connect the unattached end of the USB cable to your smartphone. This action will cause your device to boot automatically into EDL mode, making the process seamless and easy to follow.

Method 4: By Hardware Test Points / Restore Your device

1. Begin by downloading the QDLoader driver onto your computer.
2. Identify the EDL PinOUT/Test Point on your smartphone (refer to the given image for guidance).
3. Use a metal tweezer or a conductive metal wire to create a connection, or short, between the identified points.
4. After successfully shorting the points, connect your smartphone to your PC using a USB cable.
5. Congratulations! Your device should now be in EDL mode.
6. Now you’re ready to launch any of the following tools – QFil, QPST, QFlash, or MI Flash Tool – to flash the firmware and restore your smartphone.

Method 5: Using EDL Test Point

Disconnect the battery connector and then link the two specified test points. When you connect your device, the phone’s Qualcomm port will be displayed.